Yongkang Jiaxiao Electric Welding Automation Equipment Co.,Ltd Yongkang Jiaxiao Electric Welding Automation Equipment Co.,Ltd
Yongkang Jiaxiao Electric Welding Automation Equipment Co.,Ltd
Product category
  Spot welding machine
  Foot spot welding machine
  Air power spot welding machine
  Projiection welding machine
  龙门式网片自动焊机
  Stored energy spot welding machine
  Row of welding machine
  Reticle products manufacture equipments
 
  Butt welding machine
  Foot Butt Welder
  Air Power Butt Welder
  Air Power Butt Flsh Welder
  Hydraulic Butt Flash Welder
  Seam welding machine
  vertical/horizontal seam welding machine series
  circular seam welder series
  Whole set of special machine
  whole set of stainless steel cistern equipments
  complete sets of solar water heater equipments
  security door automatic welding machine series
  Various welding equipments
  Various welding equipments
    Search
Products
     
   Home > Products
Burglary-resisting door bull welder(TN-150-5)
To Burglary-resisting door bull welder (TN-150-5) interested in, click here to feedback your information, we will contact you as soon as possible! Please: + 86 579-87527838
Characteristics

Novel structure, unique design, good rigidity. Adopting high precision steering mechanism, good abrasion resistance, the pistons, welding speed method.natural pressure, pressure stability.

Burglary-resisting door welding platform facilitate customer installations, alloy door of guard against theft, welding, such as stainless steel categories is analyzed, much more than the welding head solder welding.

Microcomputer constant pressure control system, two sections of discharge, precise control welding time and welding current, convenient adjustment.

High magnetic structure, subprime XiGangPian output current is big, energy conservation and environmental protection.

The post-cooling water transformer, the post-cooling water electrode head post-cooling water SCR, improve the life of the equipment.

Which is used widely for automotive, aviation industry, electronics, household appliances, etc.

Used for low carbon steel, alloy steel, non-ferrous metal tubes, rods, plate material or between different metal welding.

Parameters

model number

TN-63

TN -80

TN -100

TN -150

TN -200

Power input

380V

380V

380V

380V

380V

Nominal capacity

63KVA

80KVA

100KVA

150KVA

200KVA

Load sustained rate

20%

20%

20%

20%

20%

Maximum clamping force

6.1KN

6.1KN

10KN

10KN

10KN

Rated the primary current

166A

230A

266A

410

528A

Subprime maximum current

17KA

23KA

29KA

36KA

42KA

Subprime no-load voltage

6.8V

7.8V

8.8V

10.5V

11.8V

Welding ability

Φ4.0+4.0

Φ4.5+4.5

Φ5.0+5.0

Φ6.0+6.0

Φ7.0+7.0

 Installation and maintenance

1. Installation

Should as far as possible installed in power transformer substation room (wet sex dust near less, without harmful gas flat on the ground, and certain fixed anchor bolt.

And welding jig combination when installed, welding and welding ontology completely insulation must be.

2. The welding power of connection

(1) the welding power and welder ontology to connect the power terminal behind.

(2) the power supply capacity and the selection of connecting to guarantee: when welding, the primary voltage pressure drop no more than 10% of normal rated primary voltage.

(3) per welding machine must be equipped a power switch, and the fuse configured with capacity.

By electric power supply cord installation should Washington professional personnel.

3. Cooling water piping

Will pick up in the body with rubber water to nozzle and drain profile, conjunction is in, prevent leakage.

Please use do not contain impurities especially salt and calcium containing high quality water (electrical resistivity 5k cm above). Ω long within the conduit to generate scale, cause leakage accidents. Especially the coast of groundwater, salt content, should pay full attention to.

4. Compressed air with piping

Thoroughly clean the pipe on scraps, dust, will air rubber tube is connected in the inlet side welding ontology, make not leak.

Please use compression in the air above 0.7 MPa, gas supply pressure with rubber to ensure in 0.5 ~ between 0.7 MPa. Air compressor capacity or piping of small size, cause gas supply deficiency can make back pressure head sluggish.

5. Pedal switch connection

Pedal switch plug into the socket below the positive, and screw down.

6. Grounding

To prevent insulation resistance, low electric operator grounding is very important. 14mm2 above should be used with the grounding wires welder grounded. (grounding should by electrical professionals)

 

cautions

1, welding operations

In welding, absolutely cannot will hand puts add pressure between electrodes, electrode to thousands of Newton, to hurt.

2 and electrode head overhaul, plastic, replacement

Overhaul, plastic, replacement electrode top, must close control device of the power switch.

Three, internal overhaul

Maintenance welder airframe internal and control device or replacement parts etc, must cut off power supply.

4, tectonic change

Please do not arbitrarily change the machine structure or specifications, if needed, please contact with distributors or the company, and especially need to pay attention to the following:

If you need in welder (install welding jig, must will tooling and electrode conductive belt or tooling and body shell, otherwise, completely insulation between the welding current, the shunt to welding jig caused components damage.

(2) do not change welder internal temperature switches or transformed.

5, maintenance and repair

Please do according to instructions for maintenance, repair, otherwise not only cannot fully exert the function of welding machine, still can greatly shorten the using life.

6, protection appliance dress

Welding produces splash, please wear protective clothing, lens, protective gloves and other protective tools.

Quality assurance

This machine factory has strict check, to prevent in case of failure, the company produces warranty card, issued after reading, please keep (entrust repair warranty card), the need.

If the welder malfunction needs to be repaired, please specify welding type, manufacturing Numbers, fault content, timely and distributors or the company contact.

Name:   * Model:   *
Num:   * Pay:
Company:   *
Address:   *
Linkman: Sir Miss * Mobile:   *
Tel Phone:  * Fax:   *
 
Back